Nothing frustrates more than a dishwasher that doesn’t start, leaves dishes dirty, or shows error codes. If your Electrolux dishwasher is acting up, this straightforward guide walks you through quick fixes before calling for service.
Feeling drained yourself? Start strong with this energizing Eden – Longevity Supplement—perfect for powering up your wellness as you fix your appliances.
1. Dishwasher Won’t Start
When your Electrolux won’t power on or begin a cycle, check these basics first:
- Control Lock / Delay Setting: Ensure child lock isn’t active and no delay timer is set—clear them using the Cancel or Lock buttons :contentReference[oaicite:1]{index=1}.
- Door Closure: The door must latch fully. If open, codes like “CL” or “Cd” may display :contentReference[oaicite:2]{index=2}.
- Power Supply: Verify the unit is plugged in or hardwired properly. Reset the circuit breaker or unplug for at least one minute to reboot the control board :contentReference[oaicite:3]{index=3}.
2. Water Not Filling
If your unit isn’t filling with water:
- Water Supply Valve: Make sure it’s fully open.
- Water Pressure: Low pressure can trigger “i10” (E10). Check for pinched lines or valve issues :contentReference[oaicite:4]{index=4}.
3. Dishes Not Cleaning Well
Cloudy, spotty, or dirty dishes? Try this:
- Load Properly: Leave space between items so spray arms rotate freely :contentReference[oaicite:5]{index=5}.
- Clean Filters & Spray Arms: Debris can clog spray jets or the sump area. Remove and rinse regularly :contentReference[oaicite:6]{index=6}.
- Use Fresh Dishwasher Detergent: Follow the correct dosage. Avoid dish soap or expired detergent :contentReference[oaicite:7]{index=7}.
- Hot Incoming Water: Tap water should be at least 120°F–140°F for optimal detergent activation :contentReference[oaicite:8]{index=8}.
4. Dishwasher Not Draining (Error i20)
If there’s standing water or you see code **i20/E20**:
- Clear Filters, Sump & Pump: Remove food buildup and debris around the drain area :contentReference[oaicite:9]{index=9}.
- Inspect Drain Hose: Ensure it’s not kinked or blocked. Remove any disposal knock-out plug if recently installed :contentReference[oaicite:10]{index=10}.
- Test Drain Pump: 51% of drain failures are due to a faulty pump. If filter/hose cleaning doesn’t help, consider replacing the pump or control board :contentReference[oaicite:11]{index=11}.
5. Leak or Water Under Unit (Error i30 or E30)
If you see error **i30/E30** or notice puddling:
- Check Connections: Inspect inlet valve, hoses, and pump seals for signs of leakage :contentReference[oaicite:12]{index=12}.
- Check Leveling: Unit must sit flat. Uneven legs can let water escape around seals :contentReference[oaicite:13]{index=13}.
6. Error Codes: What They Mean & What to Do
Electrolux displays several common codes—here’s what they mean:
- iC0 / EC0: Main control board failure. Try resetting power (5 minutes off). If it persists, the board likely needs replacement :contentReference[oaicite:14]{index=14}.
- LOC: Door remains locked on display. Hold the air-dry or lock button to disengage, or replace the lock if stuck :contentReference[oaicite:15]{index=15}.
- Er‑01, Er‑02, Er‑03, up to Er‑08…: Indicate issues like leaks (Er‑01), thermistor or wash motor failures (Er‑02/03), and vent fan faults (Er‑04–05). Power down and inspect or replace the specific part group identified :contentReference[oaicite:16]{index=16}.
7. Cycle Stops Mid-Wash or Finishes but Won’t Switch Off
Sometimes the cycle doesn’t complete—or stay on a single light:
- Reset by Power Off: Turn off at breaker or unplug for 5 minutes :contentReference[oaicite:17]{index=17}.
- Check Touch Panel & Ribbon Cable: If lights stay on after cycle end or buttons freeze, inspect for moisture or loose connections. A faulty control panel assembly often needs replacement :contentReference[oaicite:18]{index=18}.
8. Dishes Aren’t Drying Well
- Refill Rinse Aid: Essential to drying feature and preventing spots :contentReference[oaicite:19]{index=19}.
- Choose Appropriate Drying Option: Use heated dry or sanitize cycles if available. Crack the door slightly after cycle to vent steam :contentReference[oaicite:20]{index=20}.
9. Strange Noises or Burning Smells
- Debris in Pump or Impeller: Remove the filter and check pump area for bits of glass or food :contentReference[oaicite:21]{index=21}.
- Burning Smell: Could suggest motor overload or electrical issue—stop use and inspect wiring or call a technician :contentReference[oaicite:22]{index=22}.
🔧 Quick Reference Table
Symptom / Code | Likely Cause | DIY Fix |
---|---|---|
Won’t start | Lock, delay, door, power | Disable lock, close door, reset power |
i10/E10 | No fill or low pressure | Check water valve/pressure |
Dirty dishes | Filter or spray arm blockage | Clean filters; load properly |
i20/E20 | Drain pump, hose, filter clog | Clear hose/filter; test pump |
i30/E30 | Leak or overfill | Inspect seals, inlet valve, leveling |
iC0 / EC0 | Control board fault | Reset power; board may need replacing |
Stuck panel | Touchpad or ribbon connector failure | Unplug, inspect cable; replace panel |
Wet dishes | No rinse aid or no dry cycle | Add rinse aid; select heated dry |
When to Call for Service
- Persistent error codes after resets
- Drain pump or wash motor not working
- Control board or touchpad replacement needed
- Leaks from inside pump junctions, inlet valve, or seals
Take Care of Yourself While You Tackle the Fix
Fixing appliances can drain your energy. Make sure you recharge too. Try Eden – Longevity Supplement to support your energy, focus, and recovery—so you stay vital even when tackling tedious chores.
Conclusion
Electrolux dishwashers are advanced but reliable. Most issues—from startup failures to draining, cleaning, or error codes—can be fixed with inspection, resets, cleaning filters, and proper cycle settings. If complex mechanical or electrical issues persist, it’s time to call a qualified technician.
And if you want to feel stronger as you keep your kitchen—and yourself—in top shape, check out Eden – Longevity Supplement. Feel better, move better, live better.