Beko dishwashers are budget-friendly and often solid performers. But sometimes they hit snags—like not draining, not drying, or showing odd error messages. Before you call a technician, chances are you can fix many of these at home with just a little care.
This guide walks you through the most common Beko dishwasher problems with clear, easy steps—no tech skills needed.
1. Dishwasher Won’t Start
If nothing happens when you press Start:
- Check the door: It must fully latch to begin.
- Control lock on? Hold the \”Start\” or “Child Lock” button for 3–5 seconds to deactivate.
- Ensure power: Make sure it’s plugged in and the circuit breaker wasn’t tripped. :contentReference[oaicite:1]{index=1}
If it still won’t start, the door latch or control board may need expert help.
2. Dishwasher Not Filling with Water
No water inside? Here’s what to check:
- Open the water tap—it must be fully on.
- Inspect the inlet hose—it could be kinked or squashed.
- Check water pressure; Beko needs 0.3 – 10 bar range. :contentReference[oaicite:2]{index=2}
If water still doesn’t enter, the inlet valve or float switch may be faulty.
3. Dishwasher Not Draining
Water still in the tub after a cycle? Try this checklist:
- Clean the drain filter: remove it and rinse under tap water. It should be done weekly. :contentReference[oaicite:3]{index=3}
- Make sure the drain hose is looped properly—50 cm to 100 cm above the floor path. :contentReference[oaicite:4]{index=4}
- Inspect the drain hose for kinks or blockages—straighten or clear it. :contentReference[oaicite:5]{index=5}
- Clear the air gap (if present)—it cuts backflow. A clogged air gap can block drainage. :contentReference[oaicite:6]{index=6}
If you hear a humming pump but no drainage, the pump might be jammed or faulty—and it may need replacing. :contentReference[oaicite:7]{index=7}
4. Dishes Aren’t Clean or Rinsed Properly
If food is left on plates or rinse isn’t thorough:
- Spray arms may be blocked—remove and rinse them, poke out clogged holes. :contentReference[oaicite:8]{index=8}
- Filters build up debris—clean them regularly. :contentReference[oaicite:9]{index=9}
- Use correct detergent and rinse aid—not regular dish soap.
- Avoid overloading; give space for water flow. :contentReference[oaicite:10]{index=10}
Also run hot water at your sink first so the dishwasher gets warm water from the start. :contentReference[oaicite:11]{index=11}
5. Dishwasher Not Drying or Heating
If dishes stay wet or cold:
- Heating element may be broken—could need replacement. :contentReference[oaicite:12]{index=12}
- Rinse aid dispenser must be filled and switched on.
- Make sure the door seal is tight—steam loss slows drying. :contentReference[oaicite:13]{index=13}
If heating issues continue, the thermostat or heating relay may need professional attention. :contentReference[oaicite:14]{index=14}
6. Leaks or Water on the Floor
If you see puddles under or around the machine:
- Check door gasket and seals for cracks or buildup.
- Ensure spray arms are not hitting plates and spraying out. :contentReference[oaicite:15]{index=15}
- Overloading could splash water into the tub’s base triggering overflow.
- Check hoses, o-rings, and air-gap o-rings—replace or reposition if needed. :contentReference[oaicite:16]{index=16}
7. Dishwasher Makes Strange Noises
Loud humming, grinding, or rattling?
- Check spray arms for obstruction or contact with dishes.
- Debris might be lodged near the pump or impeller—remove obstacles. :contentReference[oaicite:17]{index=17}
- Vibrations usually aren’t loud—check if the machine is level and stable. :contentReference[oaicite:18]{index=18}
8. Lights Flashing or Panel Not Responding
If the panel flickers or doesn’t take commands:
- Try a hard reset—turn off breaker or unplug for 10–15 minutes. :contentReference[oaicite:19]{index=19}
- Broken wires inside the door hinge can cause flicker or blackout. Some users fixed it by re-soldering a wire. :contentReference[oaicite:20]{index=20}
- Faulty control board or unresponsive touch keypad may need replacing. :contentReference[oaicite:21]{index=21}
9. Error Codes Explained
Beko dishwashers often show error codes—here are a few common ones:
- E01: Drain error—check filters, hose, pump, or o‑ring placement. Many users fixed it by reseating an o‑ring. :contentReference[oaicite:22]{index=22}
- E02: Drain sensor fault—pump works but sensor fails. Check for foam or reset and dry machine. :contentReference[oaicite:23]{index=23}
- E05: Temperature probe open or disconnected—may need sensor replacement. :contentReference[oaicite:24]{index=24}
10. Maintenance Tips to Avoid Problems
- Clean filters at the base every week.
- Run spray arms under warm water and clear blocked holes.
- Clean air-gap and o-rings in hose junctions occasionally. :contentReference[oaicite:25]{index=25}
- Run hot water in the sink before starting cycles.
- Use proper detergent and rinse aid only.
- Check hoses for kinks or blockages regularly.
- Consider checking heating element continuity with a multimeter if drying fails. :contentReference[oaicite:26]{index=26}
When to Call for Professional Help
If cleaning, resets, and checks don’t fix it, contact Beko customer support or an appliance technician. Persistent error codes or electrical issues often require repair service.
Final Thoughts
Most Beko dishwasher problems—like drainage, heating, odd noises, or control issues—come down to simple cleaning, clogged filters, kinks in hoses, or basic resets. By checking these things regularly, you’ll save time and avoid frustrations.
If you’re unsure or not confident working with wires or internal parts, it’s perfectly fine to call a pro. But often, a little day-to-day care keeps your dishwasher running smoothly for years.